Controller chassis with large form-factor drive bays (CBSL)

Virtual Storage Platform G130 Hardware Reference Guide
Version
88-08-0x
88-07-0x
88-06-0x
Audience
anonymous
Part Number
MK-97G130004-01

The following describes the CBSL controller chassis technical specifications and associated physical features of the controller.

CBSL mechanical specifications

The following table provides a description and specifications of the CBSL controller chassis.

Item

Description

Chassis (2U)

DW800-CBSL

Controller board

DW-F850-CTLXSFA

DW-F850-CTLXSCA DW-F850-CTLXSSA

Number of DIMM slot

1

Cache memory DIMM capacity per controller

16 GiB

Total cache memory capacity per system

32 GiB

Control memory

Flash memory: 32 MB

L3 cache memory: 4 MB

SDRAM: 1 GB

Data assurance method

Data bus: Parity

Cache memory: ECC (1-bit correction, 2-bit detection)

Drive: Data assurance code

Available drive slots

12

Physical dimension

(W x D x H) (mm)

483 × 813 × 88 mm

Weight/Mass (kg)

(Approximate)

15.9 kg

Start-up time (min)1

5 to 8 (min)

Required height

(EIA unit)2

2U

Heat output (W)

192 W

Power consumption (VA)

200 W

Insulation withstand voltage

AC 1,500 V (100mA, 1min)

Insulation resistance

DC 500 V, 10 MΩ or more

Air flow (m3/min)3

3.5 (m3/min)

Notes:
  1. Start-up times might be longer depending on the number of drive trays connected. With a maximum configuration 1 controller chassis and 7 drive trays, start-up time is approximately 8 minutes.
  2. Can be mounted on the Hitachi Universal V2 rack.
  3. Value shown is the maximum value.

Host interface specifications

The following table lists the specifications of the host interfaces available for the VSP G130 controllers.

Item

Specification

Interface type

16 Gbps FC (Optical)

Data transfer speed

(Max. speed for transfer to host)

400 Mbps (FC)

800 Mbps (FC)

1600 Mbps (FC)

Number of ports per controller

16 Gbps FC (Optical): 2

Number of ports per system

4

Battery life specifications

Storage system intake temperature CBSL

Up to 75.2º F (24º C)

5 years

Up to 86º F (30º C)

4 years

Up to 93.2º (34º C)

3 years

Up to 104º (40º C)

2 years

CBSL component LEDs

The following table describes the definitions of the CBSL controller front panel bezel LEDs.



Number Item Color Pattern Description
1 POWER LED Green ON Storage system is powered on.
Amber ON Storage system is receiving power.
2 READY LED Green ON Storage system is ready for normal operation.
3 WARNING LED Amber ON Component requires maintenance.
Blink

Failure occurred. Requires maintenance.

When the SIM is confirmed, the LED pattern indicates the failure and requires attention.

Note: When System Option Mode 1097 is set to ON, the WARNING LED does not blink, even if the following failure service information messages (SIM) are issued: 452xxx, 462xxx, 3077xx, 4100xx, and 410100.

LED might turn off during user maintenance.

4 ALARM LED Red ON Processor failure (system might be down). For assistance, contact customer support: https://support.hitachivantara.com/en_us/contact-us.html.
5 POWER ON/OFF (main switch) - - Turns on power to the storage system.
6 Lock - - Locks and unlocks the front panel bezel by using the supplied key.
Note: Removing a controller can cause the POWER, READY, WARNING, and ALARM LEDs on the front panel to turn off. These LEDs return to their on state after the storage system recovers from the controller replacement.

The following table describes the definitions of the CBSL controller front panel LEDs without an attached front bezel.



Number Item Color Pattern Description
1 ACT LED Green ON Normal operation.
Blink Drive is being accessed.
2 ALM LED Red ON Drive stopped due to a failure and can be replaced.
3 POWER, READY, WARNING, and ALARM LEDs - -

Refer to the previous table.

Note: When System Option Mode 1097 is set to ON, the WARNING LED does not blink, even if the following failure service information messages (SIM) are issued: 452xxx, 462xxx, 3077xx, 4100xx, and 410100.

4 POWER ON/OFF (main switch) - - Turns on power to the storage system.
5 Large form-factor drive slots - - Twelve 3.5-inch large form-factor drives are positioned horizontally in the slots. The slots are organized from 0 to 11 in the following order: 
8   9   10  11
4   5   6   7
0   1   2   3

The following table describes the definitions of the CBSL controller real panel LEDs.



Number Item Color Pattern Description
1 Port LED Red ON A failure occurred in the small form-factor pluggable (SFP).
Blue ON Normal link status at 16-Gbps (16-Gbps SFP)
Green ON Normal link status at 4-Gbps or 8-Gbps (16-Gbps SFP)
2 LAN LED Amber ON LAN-RST is pressed.
3 Battery status LED Green ON Battery charge is complete.
Blink Battery is charging or discharging.
- OFF Battery indicates the following status:
  • The battery is not installed.
  • A failure occurred.
4 Backup status LED Green ON Restoration in progress following loss of power.
Fast blink Restoring. Blinking five time per second.
Slow blink Restoring or sequential shutdown in progress. Blinking once per second.
5 SAS port LED Blue ON Link to port is established.
6 Controller (CLT) ALM LED Red ON Controller can be removed.
Blink Failure occurred to controller power supply.
Amber ON LAN switched is pressed.
7 SAS port SAS cable port.
The following table describes the definitions of the CBSL controller AC power supply unit LEDs and connectors.

Number Item Description
1 Receptacle

Connects to the power cable provided with the storage system.

2 AC IN LED

Blue: AC input is normal.

3 ALM/RDY LED

Red: Power supply unit can be replaced.

Green: Normal operation.