Large form-factor drive tray (DBL)

Virtual Storage Platform G130 Hardware Reference Guide

Version
88-08-0x
88-07-0x
88-06-0x
Audience
anonymous
Part Number
MK-97G130004-01

The following tables provide information about the DBL drive tray specifications and supported configurations for VSP G130 storage system.

Name

Model number

Height

Number of drive slots

Supported drive type

DBL

DW-F800-DBLC

2U (88.2 mm)

12

3.5 inch (LFF)

Physical specifications

Item

Specification

Physical dimension

(W x D x H) (mm)

482 × 565 × 88.2 mm

Weight/Mass (kg)

(Approximate)

17.4 kg

Start-up time (min)1

5 to 8 (min)

Height

(EIA unit)2

2U

Heat output (W)

124 W

Power consumption (VA)

144 VA

Air flow (m3/min)3

2.2 (m3/min)

Notes:
  1. Start-up times might be longer depending on the number of drive trays connected. With a maximum configuration 1 controller chassis and 7 drive trays, start-up time is approximately 8 minutes.
  2. Can be mounted on the Hitachi Universal V2 rack. For the mounting, special rails for the rack and decoration panels are required separately depending on the number of the mounted storage systems.
  3. Value shown is the maximum value.

Supported drive type

Item

Specification

Drive form-factor

3.5-inch HDD

Supported data capacity

5874.22, 9790.36 GB

Maximum mountable quantity (unit)1

12 (total per chassis)

96 (maximum per system)

Maximum number of spare drives2

16

Note:
  1. When mounting storage system and DBL drive trays, the maximum mountable quantity may vary.

  2. Available as spare or data disks.

DBL component LEDs

The following table lists the definitions of the DBL drive tray front bezel LEDs.



Number Item Color Pattern Description
1 POWER LED Green ON Drive tray is powered on.
2 READY LED Green ON Drive tray is ready for normal operation.
3 Locate LED Amber Blink

Indicates the location of the chassis.

Can be turned on or turned off by the maintenance utility.

4 Lock - - Locks or unlocks the front panel bezel by using the supplied key.

The following table lists the definitions of the DBL drive tray front LEDs without an attached bezel.



Number Item Color Pattern Description
1

POWER,

READY,

and,

LOCATE LEDs

Green ON

Drive tray is powered on.

Drive tray is under normal operation.

Amber Blink

Indicates the location of the chassis.

Can be turned on or turned off by the maintenance utility.

2 ACT LED Green ON

Drive tray is under normal operation.

Blink

Drive is being accessed.

3 ALM LED Red ON

Drive stopped due to a failure and can be replaced.

4 LFF drive slots - -

Twelve 3.5-inch large form factor drives are positioned horizontally.

The slots are organized in the following order:
8   9   10  11
4   5   6   7
0   1   2   3

The following table lists the definitions of the DBL drive tray rear panel components and LEDs.



Number Item Color Pattern Description
1 ENC - - Controller board
2 POWER LED Green ON ENC is powered on.
3 LOCATE LED Amber Blink

Indicates the location of the chassis.

Can turn on or off by the maintenance utility.

4 ALARM LED Red ON

ENC stopped due to a failure and can be replaced.

5 PATH (IN) LED Blue ON IN side port is linked up.
6 PATH (IN) connector - - Port connects to a controller or drive tray.
7 PATH (OUT) LED Blue ON OUT side port is linked up.
8 PATH (OUT) connector - - Connects to a drive tray.
9 Console - - This port is reserved.
10 Power supply unit - - Power supply unit
11 Receptacle - - Connects to the power cable provided with the storage system.
12 AC IN LED Green ON Drive tray is under normal operation.
13 ALM LED Red ON

Power supply unit stopped due to a failure and can be replaced.

14

RDY LED

Green ON

Power supply unit is under normal operation.