Installing Storage Device Launcher on the management client

System Administrator Guide for VSP E990 and VSP G130, G/F350, G/F370, G/F700, G/F900

Version
88-08-0x
Audience
anonymous
Part Number
MK-97HM85028-11

The Storage Device Launcher application is required to run Hitachi Device Manager - Storage Navigator(HDvM - SN) with Adobe AIR from HARMAN. Storage Device Launcher is included in the Web Console Launcher setup file on the SVP. Use the following procedure to download and install Storage Device Launcher on the management client.

CAUTION:
If you use other management software to access HDvM - SN (for example, Hitachi Ops Center Administrator), install Storage Device Launcher as a user with administrator permissions on the management client.
Note: If you are using one management client to access multiple storage systems, you only need to install Storage Device Launcher on the management client once.
  • You must have the model identification number of the storage system. The model identification number is the same as the folder name of the SVP firmware installation directory.
    Example: C:\Mapp\wk\936000400001
    • In this example, the 12-digit character string 936000400001 is the model identification number. The last 6 digits indicate the serial number of the storage system.
    • C:\Mapp is the default installation directory for the SVP firmware. The location of the installation directory depends on the conditions specified when the SVP firmware was installed.

    If multiple storage systems are registered on the SVP, you can use the model identification number of any storage system whose SVP firmware version supports AIR.

  1. Download the Web Console Launcher setup file for Windows from the SVP to the management client.
    • If you can log in to HDvM - SN by using a web browser, click Tool > Download in the HDvM - SN menu bar, and then download the Web Console Launcher setup file for Windows (WCLauncher_win.zip).
    • If you cannot log in to HDvM - SN by using a web browser, open the download the Web Console Launcher setup file as follows:
      1. Open a web browser on the management client, and enter the following URL:
        https://IP-address-or-host-name-of-SVP/sanproject/ToolDownload/serial-number-of-storage-system
        If you changed the port number of the protocol HTTPS from the initial value (443 by default), specify the following URL:
        https://IP-address-or-host-name-of-SVP:port-number-of-protocol-HTTPS/sanproject/ToolDownload/serial-number-of-storage-system
        Note: If the SVP firmware version is earlier than 93-02-02 or 88-06-02, enter the following URL instead:
        https://IP-address-or-host-name-of-SVP(:port-number-of-protocol-HTTPS)/dev/storage/model-identification-number/htdocs/tool/tooldownload.html
        After the download page opens, go to step (c).
      2. In the authentication window, enter the user name and password.
      3. Download the Web Console Launcher setup file for Windows (WCLauncher_win.zip).
  2. Expand the downloaded Web Console Launcher setup file.
    Make sure to expand the setup file in a folder or directory that meets the following requirements:
    • Use only 1-byte alphanumeric characters for the expanded folder or directory name.
    • Use an expanded folder (excluding directly under C: drive) that can be accessed (Read/Write) by management client users who do not have administrator permissions.
    • If you are installing Storage Device Launcher two or more times on the same management client, expand the setup file each time in the same folder or directory (the one used for the initial installation). If you expand the setup file in a different folder or directory from the first installation, other users will not be able to run Storage Device Launcher.
    Note: If a security warning or a window blocking the operation is displayed, do not expand the setup file. Change the properties of the setup file as follows and then expand the file:
    1. Right-click WCLauncher_win.zip, and then click Properties.
    2. In Security, select Unblock, and then click OK.
  3. Install Storage Device Launcher as follows:
    • If you are logged in to the management client with administrator permissions, right-click WCLauncher_win\WCLauncher\Setup_SDLauncher.bat, and run it by selecting Run as Administrator.
    • If you are not logged in to the management client with administrator permissions:
      1. Right-click WCLauncher_win\WCLauncher\Setup_SDLauncher.bat, and then click Create Shortcut.
      2. Move the created shortcut onto the desktop.
  4. Open WCLauncher_win\WCLauncher\log\Setup.log with a text editor, and confirm that "completed" is displayed.
    CAUTION:
    Do not move or delete the WCLauncher_win folder after Storage Device Launcher installation is complete. This folder contains files required for running Storage Device Launcher.