Configure alert notifications

System Administrator Guide for VSP One Block 85

Version
A0-05-4x
Audience
anonymous
Part Number
MK-26VSP1B030-03
ft:lastEdition
2026-06-22
Product
Virtual Storage Platform One Block

Alert notifications can be sent as email, SNMP trap transmission, and Syslog server transfer. Use the Alert Notifications window in the maintenance utility to configure alert notifications.

Alerts are posted over the management LAN from the static IP address of the management port of each AMC. If an AMC stops working due to a failure, you are notified from the static IP address of the management port of the known good AMC. Therefore, be sure to connect the management port of each AMC to the management LAN. If only one AMC management port is connected to the management LAN, failure information may not be reported correctly.

If the ESM reboots within about 10 minutes after an alert is issued, multiple alerts with the same issue date and time and reference code might be reported. If multiple alerts with the same issue date and time and reference code are reported, check the alerts in the maintenance utility, and then take actions for each displayed alert.

  1. In the maintenance utility, expand Administration, and then click Alert Notifications.


  2. In the Alert Notifications pane, click Set Up.
  3. On the Email tab, configure the email settings for alert notifications.


    Item Description
    Notification Alert
    • Host Report: Send alert notifications only for SIMs that are reported to the host.
    • All: Send alert notifications for all SIMs.

    This setting applies to Email, Syslog, and SNMP.

    Email Notice
    • Enable: Notify SIMs by email.
    • Disable: Do not notify SIMs by email.
    Email Address (To) Email address or addresses for sending SIMs and the types of email delivery ([To], [Cc], or [Bcc]).

    This setting is required if Email Notice is enabled.

    Email Address (From) Email address of the sender of SIM alerts.
    • Maximum number of characters: 255
    • Allowable characters: alphanumeric characters (ASCII codes) and the following symbols: ! # $ % & ` + - * / ʻ ^ { } _ . @ ~ = ?

    This setting is required if Email Notice is enabled.

    Email Address (Reply to) Email address to which replies are sent. If you omit this item, replies from the email receivers are sent to Email Address (From).
    • Maximum number of characters: 255
    • Allowable characters: alphanumeric characters (ASCII codes) and the following symbols: ! # $ % & ` + - * / ʻ ^ { } _ . @ ~ = ?
    Description to Notify Content that appears at the beginning of the alert notification emails.
    • Maximum number of characters: 511 one-byte characters
    • Symbols: ! " # $ % & ' ( ) * + - . / : ; < = > ? @ [ \ ] ^ _ ` { | } ~
    • One-byte spaces
    • Line feeds (a line feed counts as two characters)

    This setting is required if Email Notice is enabled.

    Mail Server Settings - Mail Server IPv4, IPv6, or host name (Identifier) of the mail server. You cannot set all 0 (zero) as the IP address.

    Identifier: maximum 255 alphanumeric characters (ASCII codes) and symbols: ! $ % - . @ _ ` ~

    This setting is required if Email Notice is enabled.

    Mail Server Settings - SMTP Authentication
    • Enable: Use SMTP authentication.
    • Disable: Do not use SMTP authentication.

    If you select Enable, enter the Account and Password: maximum 255 alphanumeric characters (ASCII codes) and symbols: ! $ % - . @ _ ` ~

  4. On the Syslog tab, configure the syslog settings for alert notifications.


    Item Description
    Notification Alert
    • Host Report: Send alert notifications only for SIMs that are reported to the host.
    • All: Send alert notifications for all SIMs.

    This setting applies to Email, Syslog, and SNMP.

    Transfer Protocol
    • TLS/RFC5424
    • UDP/RFC3164
    Primary Server
    • Enable: Send SIM alerts to the Syslog server in Syslog format.
    • Disable: Do not send SIM alerts to the Syslog server.
    Primary Server - Syslog Server IPv4, IPv6, or host name of the Syslog server.
    • You cannot set all 0 (zeros) as the IP address.
    • Host name: select Identifier and enter up to 255 alphanumeric characters (ASCII codes) and symbols: ! $ % - . @ _ ` ~

    This setting is required if Primary Server is enabled.

    Primary Server - Port Number Port number to be used on the Syslog server.

    This setting is required if Primary Server is enabled.

    Primary Server - Client Certificate File Name Click Choose File, and then select the certificate file.

    Specify this item when the transfer protocol is TLS/RFC5424 and Primary Server is enabled.

    • Make sure to set this item when changing the certificate from inactive to active.
    • After applying this setting, if the certificate is not set (blank) when applying the setting again, the previously updated certificate is used.
    Primary Server - Password Password for the client certificate:
    • Maximum length: 128 characters
    • Allowed characters: alphanumeric characters (ASCII codes) and symbols: ! # $ % & ' ( ) * + , - . / : ; < = > ? @ [ \ ] ^ _ ` { | } ~.

    Specify this item when Client Certificate File Name is specified for Primary Server.

    Primary Server - Root Certificate File Name Certificate file. Click Choose File, and then specify the certificate file.

    Specify this item when the transfer protocol is TLS/RFC5424.

    • Make sure to set this item when changing the items of the certificate from inactive to active.
    • After applying the setting, if the certificate is not set (blank) when applying the setting again, the previously updated certificate is used.

    This setting is required if Primary Server is enabled.

    Secondary Server
    • Enable: Send SIM alerts to the secondary server in Syslog format.
    • Disable: Do not send SIM alerts to the secondary server.
    Secondary Server - Syslog Server IPv4, IPv6, or host name of the Syslog server.
    • You cannot set all 0 (zeros) as the IP address.
    • Host name: select Identifier and enter up to 255 alphanumeric characters (ASCII codes) and symbols: ! $ % - . @ _ ` ~

    This setting is required if Secondary Server is enabled.

    Secondary Server - Port Number Port number to be used on the secondary server.

    This setting is required if Secondary Server is enabled.

    Secondary Server - Client Certificate File Name Choose File, and then select the certificate file.

    Specify this item when the transfer protocol is TLS/RFC5424 and Secondary Server is enabled.

    • Make sure to set this item when changing the items of the certificate from inactive to active.
    • After applying the setting, if the certificate is not set (blank) when applying the setting again, the previously updated certificate is used.
    Secondary Server - Password Password for the client certificate:
    • Maximum length: 128 characters
    • Allowed characters: alphanumeric characters and symbols: ! # $ % & ' ( ) * + , - . / : ; < = > ? @ [ \ ] ^ _ ` { | } ~.

    Specify this item only when Client Certificate File Name is specified for Secondary Server.

    Secondary Server - Root Certificate File Name Certificate file. Click Choose File, and then specify the certificate file.

    Specify this item when the transfer protocol is TLS/RFC5424 and Secondary Server is enabled.

    • Make sure to set this item when changing the items of the certificate from inactive to active.
    • After applying the setting, if the certificate is not set (blank) when applying the setting again, the previously updated certificate is used.
    Location Identification Name Name of the storage system that sends SIM alerts to the Syslog servers.
    • Maximum number of characters: 32
    • Allowed characters: alphanumeric characters and symbols: ! " # $ % & ' ( ) * + - . / : ; < = > ? @ [ \ ] ^ _ ` { | } ~

    Specify this item only when Primary Server or Secondary Server is enabled.

    Retry
    • Enable: Retry when the connection to the Syslog server fails.
    • Disable: Do not retry when the connection to the Syslog server fails.

    Specify this item when the transfer protocol is TLS/RFC5424.

    Retry Interval Interval when communication with the Syslog server fails: 1 to 60 seconds.

    This setting is required if Retry is enabled.

  5. On the SNMP tab, configure the SNMP settings for alert notifications.


    Item Description
    Notification Alert
    • Host Report: Send alert notifications only for SIMs that are reported to the host.
    • All: Send alert notifications for all SIMs.

    This setting applies to Email, Syslog, and SNMP.

    SNMP Agent
    • Enable: Send SIM alerts by SNMP trap, and accept GET REQUEST, GETNEXT REQUEST, and GETBULK REQUEST.
    • Disable: Do not send SIM alerts by SNMP trap, and do not accept GET REQUEST, GETNEXT REQUEST, or GETBULK REQUEST.

    GETBULK REQUEST is supported only for SNMP versions v2c and v3.

    SNMP Version Select the SNMP protocol version.
    Sending Trap Setting
    Community
    Community name accepting the SNMP trap report.
    Set this item when the SNMP version is v1 or v2c.
    Send Trap to
    IP address that reports the SNMP trap.
    User Name
    User name used for the SNMP trap report.
    Set this item when the SNMP version is v3.
    Authentication - Mode
    Authentication mode is enabled or disabled.
    Set this item when the SNMP version is v3.
    Authentication - Protocol
    Authentication method when authentication by password is enabled.
    Set this item when the SNMP version is v3.
    Encryption - Mode
    Enabled or disabled.
    Set this item when the SNMP version is v3.
    Encryption - Protocol
    Encryption method when encryption is enabled.
    Set this item when the SNMP version is v3.
    Request Authentication Setting
    Community
    Community name that accepts the GET REQUEST, GETNEXT REQUEST, and GETBULK REQUEST.
    Set this item when the SNMP version is v1 or v2c.
    GETBULK REQUEST is supported only for SNMP versions v2c and v3.
    Requests Permitted
    IP address that accepts GET REQUEST, GETNEXT REQUEST, and GETBULK REQUEST.
    Set this item when the SNMP version is v1 or v2c.
    GETBULK REQUEST is supported only for SNMP versions v2c and v3.
    User Name
    User name that accepts GET REQUEST, GETNEXT REQUEST, and GETBULK REQUEST.
    Set this item when the SNMP version is v3.
    Authentication - Mode
    Authentication mode by password is enabled or disabled.
    Set this item when the SNMP version is v3.
    Authentication - Protocol
    Authentication method when authentication by password is enabled.
    Set this item when the SNMP version is v3.
    Encryption - Mode
    Enabled or disabled.
    Set this item when the SNMP version is v3.
    Encryption - Protocol
    Encryption method when encryption is enabled.
    Set this item when the SNMP version is v3.
    System Group Information - Storage System Name Name of the storage system. This setting is required.
    • Maximum number of characters: 180
    • Allowed characters: alphanumeric (ASCII codes) and symbols
    • Do not use these symbols: \ , / ; : * ? ” < > | & % ^
    • Do not enter a blank for the first or last character.

    If you change this item, the storage system name in the Storage System window of the maintenance utility and Web Console is also changed.

    System Group Information - Contact Contact information such as administrator name and telephone number.
    • Maximum number of characters: 180
    • Allowed characters: alphanumeric (ASCII codes) and symbols
    • Do not use these symbols: \ , / ; : * ? ” < > | & % ^
    • Do not enter a blank for the first or last character.

    If you change this item, the contact in the Storage System window of the maintenance utility and Web Console is also changed.

    System Group Information - Location Installation location of the storage system.
    • Maximum number of characters: 180
    • Allowed characters: alphanumeric (ASCII codes) and symbols
    • Do not use these symbols: \ , / ; : * ? ” < > | & % ^
    • Do not enter a blank for the first or last character.

    If you change this item, the location in the Storage System window of the maintenance utility and Web Console is also changed.

    SNMP Engine ID Enter the SNMP Engine ID.
    • If you do not need to specify the SNMP Engine ID, select Create Random ID.
    • If you want to specify the SNMP Engine ID, enter10 to 64 hexadecimal digits so that the number of characters is even.
  6. When you are finished configuring alert notifications, click Apply.
  7. When the confirmation window appears, click OK.